Silage tonnage calculator
How many tons are in the bunker, pile, bag or tower? Wet tons and dry-matter tons from the volume and a packing density, the way Nebraska and Iowa State extension do it.
If the pack is crowned, use the average depth, not the peak.
Silage in storage
360.0 wet tons
| Dry-matter tons | 126.0 t |
| Volume | 18,000 ft³ |
| Dry-matter density | 14.0 lb/ft³ |
| Wet density at 35% DM | 40.0 lb/ft³ |
| Wet weight | 720,000 lb |
How bunker tonnage is calculated
Volume is length × width × average depth, in feet. The weight of dry matter is that volume times the dry-matter density. Wet tons depend on moisture:
wet tons = length × width × depth × (DM density ÷ dry-matter fraction) ÷ 2,000
University of Nebraska CropWatch starts from a packed density of 14 lb of dry matter per cubic foot. At the usual 35% dry matter (65% moisture), that is 40 lb per cubic foot wet. Their worked example — a 50 × 30 × 12 ft bunker — is 18,000 cubic feet, or 360 wet tons.
Iowa State C6-82 instead estimates density from depth: 7.5 + 0.4 × depth (feet) pounds of dry matter per cubic foot for corn silage, and 5.4 + 0.28 × depth for haylage. A 12-foot corn silage pack is 12.3 lb DM/ft³, a bit under the 14 lb target. Switch the density control to compare the two.
Piles, bags and towers
A drive-over pile is treated as a triangle or trapezoid along the length, with optional end ramps. A bag or tower is a cylinder. Bags are often packed a little lighter than a well-packed bunker; a measured density is better than the 14 lb default.
Once you have tons, you can price the crop with the silage value calculator, check the pack with the packing calculator, or take storage losses out with dry matter shrink.
Guides
Frequently asked questions
- How do you estimate tons in a bunker?
- Multiply length × width × average depth to get cubic feet, then multiply by the wet density and divide by 2,000. Wet density is the dry-matter density divided by the dry-matter fraction. UNL’s example uses 14 lb of dry matter per cubic foot at 35% dry matter, which is 40 lb per cubic foot wet, or 360 tons in a 50 × 30 × 12 ft bunker.
- What density should I use?
- If you have a measured pack, enter it. Otherwise 14 lb of dry matter per cubic foot is the common well-packed target (UNL, Wisconsin, Cornell). UNL Beef often cites 15 lb. Iowa State’s C6-82 formula estimates density from the depth of the silage and gives a lower number in shallower bunkers.
- Does this replace a scale or a forage analysis?
- No. These are planning estimates. Moisture, packing and spoilage vary. Use a scale and a dry-matter test when you buy, sell or inventory feed.
Other calculators
- Corn silage value calculatorBreak-even price in the field, delivered to storage and at the bunk (Missouri G4591).
- Packing density calculatorHolmes and Muck packing factor, estimated dry-matter density and storage loss.
- Dry matter shrink calculatorStorage losses by silo type, and remaining tons at a new moisture.
- Earlage value calculatorValue a ton of earlage from the corn price plus a residue value (SDSU).
- Cattle pencil shrink calculatorPay weight, net $/cwt and a comparison of two sale-barn or direct bids.
- Forage chartsTypical dry matter, density and yield notes by crop.
Sources
- University of Nebraska–Lincoln CropWatch: Estimating the Tonnage of Silage in a Bunker Silo (Dorn, 2012)
- Iowa State University Extension, Ag Decision Maker C6-82: Storage Capacity for Grains, Forages and Liquids (updated April 2025)
- UNL Beef: Silage Considerations (packing target of about 15 lb DM/ft³)
Estimates for planning. Density, moisture and shrink vary with the crop, packing and weather. Don't rely on these figures for insurance claims, inventories or a sales contract. Methodology. Sister site: grainshrink.com for grain moisture shrink and bin capacity.